Full-flake floor coating
Textured, forgiving with dust and dirt, and tough enough for hot tires and heavy use. Most garages are done in a day.
Diamond grind, base coat, full flake broadcast, clear polyaspartic topcoat
About flake floorsGarage floor coatings for North DFW homes
Full-flake floors in 36 Torginol blends for Flower Mound, Southlake and nearby towns. Diamond-ground prep, a clear polyaspartic topcoat, and most garages finished in one day.
- 10-year written warranty against peeling
- Diamond grinding on every floor, never acid etch
- Free on-site estimate with flake samples
Get a free estimate
We measure on site and give you a written quote. No obligation.
Call or text us and we'll set up your free on-site estimate.
Call or text (469) 708-8407Email [email protected]- Free on-site estimateMeasured in person, quoted in writing
- One-day installTypical for flake floors on standard garages
- 10-year warrantyAgainst peeling and delamination
- Pay 30% to scheduleBalance after your final walkthrough
One floor system, done properly
We install one thing and do it well: a full-flake floor with a clear polyaspartic topcoat, ground, repaired and bonded into the concrete. You choose the blend.
36 Torginol flake blends
Every blend in the Torginol Flake sample deck, from crisp light grays to warm tans and deep charcoals. We bring the physical deck to your estimate.
Light, gray, warm, dark and blue-accent blends
See the blendsCrack repair and prep
Included with every floor. Cracks, pitting and old coatings are handled before anything goes down, because prep is what decides how long a floor lasts.
Crack cutting and filling, spall repair, coating and sealer removal
How we back it upDomino · FB-411
Torginol Flake sample deck
Choose from 36 Torginol blends
Every full-flake floor we install uses Torginol vinyl flake, and every blend in the Torginol Flake sample deck is available. Tap a blend to see it on a floor.
Screen colors are approximations built from each blend's published chip mix. We bring the physical Torginol sample deck to every estimate so you can choose in your own garage light. The deck also shows Gracious in three chip sizes (1/4", 1/8" and 1/16") so you can compare scale.
How a flake floor goes in
One day, start to finish, for most two- and three-car garages.
Inspect and measure
We check the slab for cracks, old coatings, sealers and moisture, measure it, and give you a written quote.
Diamond grind
The whole floor is ground with dust-controlled equipment to open the concrete so the coating bonds into it, not onto it.
Repair
Cracks are cut and filled, pits and spalled spots are patched, and everything is ground flush.
Base coat and flake
A penetrating base coat goes down, then vinyl flake is broadcast edge to edge until no base color shows.
Scrape and topcoat
Loose chips are scraped and vacuumed, then a clear polyaspartic topcoat seals and hardens the surface.
Walkthrough
We walk the finished floor with you, go over cure times and care, and hand over your written warranty.
Why North Texas garages need more than paint
Garage floors here deal with three things at once: heat, moving clay soil and hot tires. In July an unconditioned garage can pass 100°F. Tires coming off a hot highway soften weak coatings and pull them up. And the expansive clay under most DFW slabs means hairline cracks are normal.
That's why one-part epoxy paint and roll-on kits tend to peel within a year or two here. They sit on top of smooth concrete instead of bonding into it, and most epoxy topcoats yellow when the garage door is open to the sun.
Our approach is built around those conditions. Every floor is diamond ground so the base coat soaks into the concrete. Cracks are repaired first. And the topcoat is polyaspartic, which handles hot tires and stays clear in UV light. Read how epoxy and polyaspartic compare.
What a quote includes
- Square footage, measured on site
- Prep and repair needed for your slab
- Stem walls and steps, if you want them coated
- Your chosen blend and topcoat
- Install date, cure times and warranty terms
Where we install
Based in Flower Mound, working across Denton, Tarrant and north Dallas counties.
What homeowners say
Reviews from Google and our customers across North DFW.
Common questions
How long does a garage floor coating take?
Most standard two- and three-car garages with our full-flake system are done in one day. You can typically walk on the floor that evening and park on it after about 48 hours.
How much does a garage floor coating cost?
Our full-flake floor is $5.50 per square foot, compared with a typical retail price of $6.75. For a typical three-car garage of 600 to 750 square feet, that's about $3,300 to $4,125. The free estimate gives you an exact written price.
Is it epoxy or polyaspartic?
Our full-flake system uses a penetrating base coat bonded into diamond-ground concrete, a full broadcast of vinyl flake, and a clear polyaspartic topcoat. Polyaspartic holds up to hot tires and won't yellow in sunlight the way many epoxy topcoats do.
Will it peel from hot tires?
Hot-tire peeling happens when a coating sits on top of poorly prepared concrete. We diamond grind every floor so the base coat bonds into the slab, and our work carries a 10-year written warranty against peeling and delamination.
Do you fix cracks first?
Yes. Cracks are cut open, filled with a repair compound and ground flush before coating. Note that North Texas slabs can keep moving, so a crack caused by ongoing foundation movement may show again over time.
Ready to see your floor options?
Free on-site estimate. Written quote. Flake samples in hand.